Difficulty
Easy
Steps
7
Time Required
5 - 10 minutes
Sections
3
- Back Panel
- 2 steps
- Battery
- 2 steps
- Wireless Card
- 3 steps
Flags
0
BackLenovo Yoga 700-11ISK
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Flip your device so that the bottom panel is facing up.
- Remove the eleven 5mm Torx T5 screws from the back panel.
Flip your device so that the bottom panel is facing up.
Remove the eleven 5mm Torx T5 screws from the back panel.
1024
Step 2
- Use a spudger to unclip clips on the front and near the USB ports on each side
- Lift the back panel off
Use a spudger to unclip clips on the front and near the USB ports on each side
Lift the back panel off
Step 3
Battery
- Remove the two 3mm Phillips #1 screws holding the battery to the laptop chassis.
- Disconnect the battery from the IO board by holding the connector by the sides and gently pulling the connector out.
Remove the two 3mm Phillips #1 screws holding the battery to the laptop chassis.
Disconnect the battery from the IO board by holding the connector by the sides and gently pulling the connector out.
Step 4
- Carefully remove the battery from the laptop.
- Make sure that all wires still connected to the laptop are out of the way and not pulled out with the battery.
Carefully remove the battery from the laptop.
Make sure that all wires still connected to the laptop are out of the way and not pulled out with the battery.
Step 5
Wireless Card
- Place the laptop with the LCD facing down so that the hinges face opposite you.
- Disconnect both ends of the two blue ZIF (zero insertion force) connectors in the upper left corner and by gently flipping the black tabs on the connector and pulling up and away from both ends of the connectors.
- Do not pull on the blue tab of the cable without lifting up the black tabs on the connectors. The cable should slide in and out effortlessly. If there is resistance when pulling the cable, double check the black tabs.
Place the laptop with the LCD facing down so that the hinges face opposite you.
Disconnect both ends of the two blue ZIF (zero insertion force) connectors in the upper left corner and by gently flipping the black tabs on the connector and pulling up and away from both ends of the connectors.
Do not pull on the blue tab of the cable without lifting up the black tabs on the connectors. The cable should slide in and out effortlessly. If there is resistance when pulling the cable, double check the black tabs.
Step 6
- Unplug the black and white wireless LAN cables in the upper left corner by gently pulling upwards.
- To reinstall a wireless LAN card, note that the black cable goes to the MAIN jack, and the white to the AUX jack.
Unplug the black and white wireless LAN cables in the upper left corner by gently pulling upwards.
To reinstall a wireless LAN card, note that the black cable goes to the MAIN jack, and the white to the AUX jack.
Step 7
- Remove the one 2mm Phillips #1 screw.
- Remove the card by pulling to the left and up.
Remove the one 2mm Phillips #1 screw.
Remove the card by pulling to the left and up.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Gabrielle Bullen
Member since: 10/06/2016
372 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 15-6, Livingston Fall 2016
Member of Cal Poly, Team 15-6, Livingston Fall 2016
CPSU-LIVINGSTON-F16S15G6
4 Members
7 Guides authored
