Difficulty
Moderate
Steps
14
Time Required
10 minutes
Sections
1
- Screen and Digitizer
- 14 steps
Flags
0
BackLenovo Yoga 2 Pro
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Screen and Digitizer
- Open the laptop and remove the two screw covers on either side of the computer near the hinges using either the tip of a flathead screwdriver or a spudger.
Open the laptop and remove the two screw covers on either side of the computer near the hinges using either the tip of a flathead screwdriver or a spudger.
1024
Step 2
- Remove the revealed two 3/16” screws using a Phillips #00 screwdriver.
Remove the revealed two 3/16” screws using a Phillips #00 screwdriver.
Step 3
- Lift the two plastic bezel pieces off using a spudger.
- Using a prying tool such as a spudger, gently lift the long plastic bezel piece away from the screen.
- Be certain to only pry the plastic piece off, not anything under it. There are fragile components beneath it.
Lift the two plastic bezel pieces off using a spudger.
Using a prying tool such as a spudger, gently lift the long plastic bezel piece away from the screen.
Be certain to only pry the plastic piece off, not anything under it. There are fragile components beneath it.
Step 4
- Remove the three 1/8” screws using a Phillips #00 screwdriver.
Remove the three 1/8” screws using a Phillips #00 screwdriver.
Step 5
- Gently remove the circuit board and set it aside.
Gently remove the circuit board and set it aside.
Step 6
- Remove the last 1/8” screw near the middle of the screen using a Phillips #00 screwdriver.
Remove the last 1/8” screw near the middle of the screen using a Phillips #00 screwdriver.
Step 7
- Slide the screen up away from the hinges and lift from the backplate.
Slide the screen up away from the hinges and lift from the backplate.
Step 8
- Fold the screen over and disconnect the LCD screen cable by lifting up the blue tab and pulling.
Fold the screen over and disconnect the LCD screen cable by lifting up the blue tab and pulling.
Step 9
- Remove the four 1/8” screws using a Phillips #00 screwdriver from the hinge on either side of the laptop.
Remove the four 1/8” screws using a Phillips #00 screwdriver from the hinge on either side of the laptop.
Step 10
- Using a Torx T5 screwdriver, remove the eleven 1/4" screws from the back of the laptop.
Using a Torx T5 screwdriver, remove the eleven 1/4" screws from the back of the laptop.
Step 11
- Gently lift off the back cover.
Gently lift off the back cover.
Step 12
- Remove the four 3/16” screws from the top of the laptop near the hinges using a Phillips #00 screwdriver.
Remove the four 3/16” screws from the top of the laptop near the hinges using a Phillips #00 screwdriver.
Step 13
- Using a metal spudger, lift up the connector by the plastic near the top.
- The connector lifts out of the computer, do not pull it to the sides.
Using a metal spudger, lift up the connector by the plastic near the top.
The connector lifts out of the computer, do not pull it to the sides.
Step 14
- Carefully remove the hinges and remove the screen.
Carefully remove the hinges and remove the screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 5 other contributors
Thomas Simko
Member since: 10/01/2015
2,444 Reputation
5 Guides authored
Badges:
14
+11 more badges
Team
Cal Poly, Team 12-14, Maness Fall 2015
Member of Cal Poly, Team 12-14, Maness Fall 2015
CPSU-MANESS-F15S12G14
5 Members
12 Guides authored
Dana Drummond - Mar 15, 2017
Reply
Thanks for the great tutorial! Any part number you can provide for this?
Hussein Raouf - Nov 15, 2017
Reply
I recently replaced my Lenovo Yoga 2 pro touch display, it was cracked and touch went crazy, the crack was from the side which made it usable by disabling the touch drivers. After a while i decided to replace the screen and get back the touch feature. but now i’m suffering that i cannot use it in tablet mode for the following reasons:
After screen replacement, when lid is closed it thinks that it is in tablet mode and screen stays on and doesn’t go to sleep mode as it was before replacement, while if I put it in tablet position screen goes off and it goes to sleep mode thinking it is in closed lid position (i think). if i just lift it up only 2 mm from tablet position it gets back on.
Please advise !!
Brittany Ann Kos - Apr 17, 2018
Reply
I tried following these steps in reverse order, but I cant get step 7. I can get the glass placed correctly, but cant get it to slide back into place. Do you have any suggestions to get this step working?
Dylan Justice - Jul 20, 2018
Reply
My Y2P camera periodically disconnects when I move the screen at the hinges. Any idea if that cable is replaceable without replacing the screen?
Oyvind Overby - Aug 27, 2021
Reply
Can you advise on how to replace the leftmost LCD cable on Yoga 2 Pro with digitizer (touch) ?