Lenovo Y410P Speakers Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Motherboard
7 steps
Speakers
2 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

Missed a Step

Oops! This guide is currently missing some important steps.

BackLenovo IdeaPad Y410P
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Removal of Bottom Panel

Remove eight M2.5 x 8mm Phillips head screws, using a Phillips #0 screwdriver, in the specified locations.
Lift the bottom cover off and set it aside.

Remove eight M2.5 x 8mm Phillips head screws, using a Phillips #0 screwdriver, in the specified locations.

Lift the bottom cover off and set it aside.

1024

Step 2

              Removal of Hard Drive

Remove the two M2.5x4mm screws using a Phillips #0 screwdriver.
Slide the hard drive out of the casing.
Be careful when handling the hard drive; rough impacts may cause data loss.

Remove the two M2.5x4mm screws using a Phillips #0 screwdriver.

Slide the hard drive out of the casing.

Be careful when handling the hard drive; rough impacts may cause data loss.

Step 3

              Remove Optical Drive

With the laptop’s bottom facing up, pull the optical drive release lever back and pull the optical drive out.
Unscrew the three M2x3mm Phillips head screws shown.
At the front edge of the laptop, empty the SD card holder by pressing on the card. This will allow for further disassembly in later steps.

With the laptop’s bottom facing up, pull the optical drive release lever back and pull the optical drive out.

Unscrew the three M2x3mm Phillips head screws shown.

At the front edge of the laptop, empty the SD card holder by pressing on the card. This will allow for further disassembly in later steps.

Step 4

              Remove Keyboard and Cables

Remove the two M2.5 x 6mm screws using a Phillips #00 screwdriver.
Disconnect the two WiFi antenna cables.
Disconnect the sound connector.

Remove the two M2.5 x 6mm screws using a Phillips #00 screwdriver.

Disconnect the two WiFi antenna cables.

Disconnect the sound connector.

Step 5

Open the laptop hinge. Tip the laptop onto its side, and use the back end of the screwdriver to push the keyboard out from the optical drive area.
Turn the laptop right side up and pry the keyboard up slowly, until it is clear of the case.
Be careful of the ribbon cable when removing the keyboard. The ribbon is still attached.
Detach the ribbon cables by opening the specified latches.

Open the laptop hinge. Tip the laptop onto its side, and use the back end of the screwdriver to push the keyboard out from the optical drive area.

Turn the laptop right side up and pry the keyboard up slowly, until it is clear of the case.

Be careful of the ribbon cable when removing the keyboard. The ribbon is still attached.

Detach the ribbon cables by opening the specified latches.

Step 6

              Removal of Palm Rest

Detach the ribbon cables by opening the specified latches.
Turn the laptop upside down and remove the M2.5x8mm screw with Phillips #0 screwdriver.
Turn the laptop on its side and pry the bottom from the top.
Only partially remove the palm rest; there is still a ribbon cable attached underneath it.
Remove the ribbon cable by opening its respective latch.

Turn the laptop upside down and remove the M2.5x8mm screw with Phillips #0 screwdriver.

Turn the laptop on its side and pry the bottom from the top.

Only partially remove the palm rest; there is still a ribbon cable attached underneath it.

Remove the ribbon cable by opening its respective latch.

Step 7

              Removal of Motherboard

Remove the specified cable on top of the motherboard.
Flip the laptop over, and remove the specified cables.
Remove the two M2.5x4mm screws with a Phillips #0 screwdriver
Remove the motherboard with hands.

Remove the specified cable on top of the motherboard.

Flip the laptop over, and remove the specified cables.

Remove the two M2.5x4mm screws with a Phillips #0 screwdriver

Remove the motherboard with hands.

Step 8

              Removal of Left Speaker

Remove two M2.0 x 3mm flathead screws on the left side (using the small flathead screwdriver).

Remove two M2.0 x 3mm flathead screws on the left side (using the small flathead screwdriver).

Step 9

              Removal of Right Speaker

Remove two M2.0 x 3mm flathead screws on the right side (using the small flathead screwdriver).

Remove two M2.0 x 3mm flathead screws on the right side (using the small flathead screwdriver).

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 3 other contributors

                    Eric Chen

Member since: 01/22/2015

868 Reputation

                                      4 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 21-21, Maness Winter 2015                        

                                                  Member of Cal Poly, Team 21-21, Maness Winter 2015 



                    CPSU-MANESS-W15S21G21                     


                                            4 Members                     


                                            6 Guides authored

Aiman Nazri - Jun 26, 2018

Hello Sir,

May I look how the speaker for y410p looks like and what is the model for the speaker? Where can I find that parts? Thanks.

beslielim96 - Sep 11, 2018

Where can i find the speaker parts?

Slice and Dice#

Missed a Step#

Introduction#

What you need#

Team#

Slice and Dice

Missed a Step

Introduction

What you need

Team